OCTAVE VST OC D2 GENERATOR
OCTAVE VST OC D2 FULL

OCTAVE VST OC D2 FULL

The three knobs (sub octave, octave up, and dry) give you full control over the sound.

OCTAVE VST OC D2 GENERATOR

The Electro-Harmonix Nano POG Polyphonic Octave Generator is a more affordable, easier to use pedal compared to the POG2. I did warn you that we’d be covering more POGs didn’t I? Package dimensions: 0.5 x 2 x 3 inches Electro-Harmonix Nano POG Polyphonic Octave Generator Pedal Most users enjoyed the Powerchord, but some felt it was a little too expensive for what it offered, and said that the notes didn’t track very well. And the overdrive creates a tone well-suited to heavier genres – rock, progressive rock, metal, and so on. It’s not hard to see why it’s called the Powerchord, though, because with the harmonies it creates, you will literally have a power chord with every note you play!Īs you would expect, you can get some huge sounds out of your bass using the Powerchord, almost as if you were playing a bass with double course strings. It accepts active or passive instruments and has a battery life of 20 hours. This pedal also comes with noise gate, overdrive, tone, and effects level controls. The more switches you activate, the bigger the harmonies. The onboard LEDs help you see which harmonies you’re about to activate before you switch them on. It creates stacked harmonies above the root note an octave up, and octave and a fifth up, and a fourth and an octave up. The Fishman Fission Bass Powerchord pedal is more than just an octave pedal. Package dimensions: 8 x 7 x 3.5 inches Fishman Fission Bass Powerchord FX Pedal Some users were a little disappointed in the quality of the build, though, especially considering the price.

Most users loved the POG2, and they even found they were able to create cello and organ like sounds using this pedal. Just know that it doesn’t always track lower notes all that well. I’m not convinced that’s the best way to utilize it, but it does allow you to create some interesting sounds.Īlthough the POG2 is often used by guitarists, it sounds quite good with a bass too. Since it’s a polyphonic octave generator, it can handle chords too. The POG2 makes it easy to add octaves below and above, and together can create a huge sound. This is a versatile pedal with many controls – there’s a section for the octaves, a section for effects (attack, lowpass filter, and detune), buttons for Q (resonance) and Dry/FX (allows you to apply to your dry signal), and finally preset controls for cycling through presets. This pedal comes with attack control, two sub-octaves, two-pole resonant low-pass filter, enhanced detune and algorithm, and a rugged die-cast chassis. This one is the Electro-Harmonix POG2 Polyphonic Octave Generator. When it comes to octave pedals, POG is kind of the king, and we have more than a few POGs to highlight on this list.

Included are some presets that run through the capabilities of the plug-in.Let’s not beat around the bush. This plug-in has the capability to easily reproduce this mod, by adjusting only a few parameters.

Many users of the Boss OC-2 pedal seek to add a hardware modification that disables the output filter and dynamics sections in order to produce a more synth-like tone.

“Listen” radio buttons allow the user to tap the audio at any stage to hear what’s happening behind the scenes, and bypass certain sections if desired.

Includes a “Scope Tuning” control to affect the zoom ratio.

A scope displays both the key signal and the output signal, so the user can see how the plug-in is operating, and help identify what controls need to be adjusted in order to track more accurately or produce the intended sound.

A DC-offset switch corrects the input signal to improve tracking on rectified or offset signals.

In phase-multiplier mode, the full dynamics of the key signal are retained.

In additive mode, dynamics for the oscillators can be controlled either by a noise gate or an envelope follower, both keyed off the input signal.

The additive mode simply mixes in the octave down signals (via user-adjustable levels and wet/dry balance), whereas the phase-multiplier mode flips the phase of the key signal, following the state of the selected oscillator.

Option for two modes of operation: additive oscillators or phase-multiplier.

Controls to all the typically fixed values for low-pass filters – both on oscillator outputs (changes tone from full square wave to pure sine, or anywhere in between) as well as on the detection circuit (which can fine-tune the accuracy of the octave-divider’s tracking).

It’s based on the popular Boss OC-2 pedal but with many more features and customisability far beyond what other octavers offer, both hardware pedals and software. Octaver OC-D2, developed by Christopher Hooker, is an octave divider vst plugin that generates signals one and two octaves below the original.

Octave vst oc d2